WHAT IS IT - BENEFITS - INSTALLATION INSTRUCTIONS - REFERENCES AND CERTIFICATIONS - MARINE ENGINES

 

WHAT IS IT?

MAGNETIC DEVICE TO ECOLOGICALLY REDUCE THE FORMATION OF TOXIC GASES WITH SENSITIVE BENEFITS ON PERFORMANCE AND CONSUMPTION

 

Power Green was created based on the scientific effects that an intense magnetic field exerts on fluids.

It is applied on diesel, petrol, gas and biodiesel engines, motor turbines, etc.

Once Power Green has been installed, it resolves all problems related to low thermal efficiency and excessive consumption of fuel, without entailing maintenance or operating costs

Power Green acts on the fuel flow exploiting the high technology of a permanent high-potential magnetic field (14,000 Gauss).The fuel molecules are compressed when they pass through it, undergoing a strong acceleration. This increase in speed of the molecules increases the temperature, favouring a rapid nebulization of the fuel inside the engine, thus producing greater flammability.

powerGreen

 

All this causes a more complete and cleaner combustion with the result of a reduction in exhaust gas emissions and a lower quantity of fuel necessary for combustion with the same power supplied.

During the combustion process, "peroxides" are formed with the oxygen of the air, which, reacting with the unburned elements, provides additional energy to the system and therefore a higher efficiency of the engine. All of this leads to a significant saving on fuel and fuel consumption. However, the primary function, which is the improvement of combustion and the increase in power, is crowned by numerous other positive effects.

powerGreen2

 

When fuel is subjected to magnetism, the hydrogen particles present in the hydrocarbons are provided with a charge that makes their bonding with oxygen in the mixture more effective, so they are aligned in an ordered system.

 

BENEFITS

EXPERIMENTAL TECHNICAL DATA :

  • Reduced fuel consumption by up to approx. 10%
  • Reduction of air pollution up to approx. 50%
  • No replacement or maintenance.
  • It can be used with any type of fuel and engine, in those served by the turbocharger, it keeps the turbines always at maximum efficiency.
  • It cleans the valves, the combustion chambers, the exhaust manifolds, eliminating the presence of oily debris and paraffin deposits.
  • The start-up in Diesel engines, even at temperatures of several degrees below zero, is facilitated.
  • With regard to exhaust gases, it gives similar performances to those obtained with the best catalytic converter, with zero running costs and higher horsepower.
  • Total recovery of chemical energy still available in unburned elements
  • Reduction of particulate matter in suspension, responsible for the opacity of fumes
 

INCREASED ENERGY AND POWER OF ENGINES

With the application on cars, trucks, motorcycles, buses, marine engines for both pleasure and industry, the improvement of the combustion process represents only a part of the positive effects. In fact, you also gain higher horsepower; you achieve the effect of keeping valves, combustion chambers and exhaust manifolds.

This results in a better engine performance and a longer life of its components but above all emissions of toxic substances from the exhaust pipe are considerably reduced (up to 50%).

From experimental tests, you get a reduction in fuel consumption of approx. 10%.

Start-up in diesel engines is facilitated, even at very low temperatures, and at the same time, the oily debris and paraffin deposits are eliminated along the supply lines.

The installation of Power Green

is easy and the benefits are enormous:

savings on fuel and

at the same time increased performance,

reduction of polluting gases and

maintenance of clean valves and exhaust manifolds.

 

 

PowerGreen3


TO IMPROVE COMBUSTION AND REDUCE FUEL CONSUMPTION IN ENGINES

It was created for endothermic engines (motorcycles, cars, buses, trucks, caravans, vans, heavy vehicles in general) based on the scientific effects of an intense magnetic field.

It reduces fuel consumption, increases power, prevents the formation of deposits in the engine by exerting a cleaning action, significantly reducing the emissions of toxic substances from the exhaust pipe.

It can be applied to petrol, diesel, methane and LPG engines, without the need for electrical connection.

 


ASSEMBLY INSTRUCTIONS

 

POWER GREEN SPEEDY:

It can be installed on motorcycles up to 250cc before the fuel injection.

 

POWER GREEN BIG:

It can be installed on motorcycles and petrol vehicles between the pump and the carburettor. On the injection system for diesel or petrol vehicles up to 3000cc, the BIG must be installed between the pump and the filter.

 

POWER GREEN TRUCK:

It can be installed between the diesel pump and the filter. To enhance the operation, a second TRUCK can be installed on the return line. It is important to check the section of the hose connection.

 

POWER GREEN SPECIAL:

For special systems on earthmoving machines and yachts an ad hoc product system can be installed.

 

 

The assembly of the product is simple: it can be assembled by technicians or DIY, tests will be carried out on the exhaust gas of the engines before and after the installation. The quantification of fuel savings, as well as the observation of cleaning effects, can only be achieved after some time.

With the savings on fuel and fuel consumption, with the overall increase in performance and the consequent economic benefits, the cost is amortised in a short time.

 

powergreen4

 

 

1 - On Petrol engines between the fuel pump and the carburettor or the injection system.  powergreen5
 powergreen7

2- On Diesel engines between the fuel pump and the diesel oil filter in the models equipped with a pump, after the diesel fuel filter in the models equipped with pump injectors.

On LPG engines between the tank and the expansion lung near the latter.

 powergreen6

 

 

In the event that the fuel supply system provides two or more fuel pumps and different fuel filtering, POWER GREEN must always be installed before the last diesel fuel filter.

With regard to vehicles or ships, equipped with a recirculating supply system, it is necessary to install an ad hoc device on the return pipe so that the fuel that is not burnt, returns to the tank, triggering the pre-treatment phenomenon which remains permanent even if the fuel were to remain indefinitely at the bottom of the tank.

This preventive and curative treatment, works on the formation of sludge, condensation and microbes (due to the deterioration of the fuel that has been inactive for too long) through the progressive dissolution of the deposits in the tanks, in the filters and in the supply lines.

 

REFERENCES AND CERTIFICATIONS

 

WARRANTY:

5 years except for breakage caused by incorrect handling, shock or opening, with consequent interruption of the magnetic field.

The warranty, which is validated by the seller or installer, warrants that the product is free from manufacturing defects and that the materials used for the construction of the components are of absolute top quality, produced in its company of Sommacampagna (VR).

The product complies with the provisions of law 443 of 21.12.1990.

WARNING:

All the devices in the series have been constructed so that the powerful magnetic field they produce, only acts inside the device. However, this does not apply to an open half. Therefore, it is advisable to avoid in any case the contact with the electronic and electrical parts of the vehicle.

 

 

 

TECHNICAL DETAILS

 

SPEEDY

-          BODY        : anticorodal aluminium worked on the lathe and oxidized

-          COUPLINGS    : tubular carrier 6 – 8 – 11 mm or according to request in OT58

-          SEAL         : o-rings standard certif. DVGW (DIN 549)

-          CORE       : FE – AISI mesh– CU – Neodymium (> 14,000 Gauss)

-          FLOW RATE     : from 0.1 to 10 lt/m

-          MAX.PRESS.   : 100°

-          CERTIF.          : CE – Magnetron – Polytechnic - TUV

-          SIZE.       : length58 mm with hose conn.108 mm, Ø 45 mm

-          WEIGHT             : 230 gr.

 

BIG

-          BODY        :anticorodal aluminium worked on the lathe and oxidized

-          COUPLINGS    : tubular carrier 6 – 8 – 11 mm or according to request in OT58

-          SEAL        : o-rings standard certif.DVGW (DIN 549)

-          CORE       : FE – AISI mesh– CU – Neodymium (> 14,000 Gauss)

-          FLOW RATE      : from 0.1 to 10 lt/m

-          MAX.PRESS.   : 100°

-          CERTIF.         : CE – Magnetron – Polytechnic - TUV

-          SIZE.        : length90 mm with hose conn.140 mm, Ø 45 mm

-          WEIGHT             : 440 gr.

 

TRUCK – SPECIAL TRUCK – SUPER SPECIAL TRUCK

-          BODY        : anticorodal aluminium worked on the lathe and oxidized

-          COUPLINGS    : tubular carrier 6 – 8 – 11 mm or according to request in OT58

-          SEAL        : o-rings standard certif.DVGW (DIN 549)

-          CORE       : FE – AISI mesh– CU – Neodymium (> 14,000 Gauss)

-          FLOW RATE      : from 0.1 to 10 lt/m

-          MAX.PRESS.   : 100°

-          CERTIF.         : CE – Magnetron – Polytechnic - TUV

-          SIZE.        : length130 mm with hose conn.180 mm, Ø 45 mm

-          WEIGHT             : 630 gr.

 

 

MARINE ENGINES

gammaGreenMotori

 

 

 

Motorboat “GIADA”

motonaveGiada

Equipped with POWER GREEN for the engine part and with GAMMA STANDARD water taken directly from the sea was treated and desalinated by osmosis. The results obtained are to be considered amazing, in addition to the elimination of the formation of limescale deposits, drinking water was obtained.

 

powerGreen8

 

 

The story

Euro Gamma Group S.r.l. is the combination of the experience of TOP CHEM S.r.l and REXITAL S.r.l, companies that have been present on the market of magnetic treatment for water for more than 25 years and leaders in their sectors...

Main services

Water Treatment - Magnetic Descaling

Fuel Treatment - Feuer and Gas Catalysts

 

Certifications

A.C.S.

Tüv Nord

Epta Nord

BIOBIT

SVGW SSIGE

The Hong Kong Polytechnic University

University of Padua

 

 

Contacts

Sommacampagna (Verona)

Via del Lavoro, 21

Tel. +39 0456090174

Fax +39 0456082426

info@eurogammagroup.it

P.IVA 04175000233